==================================================
 Agilent Infiniium 548xx Oscilloscope Recovery CD
 Operating System + Software Version 4.3
==================================================


   == DONATING, DOWNLOADING, LINKING, AND SHARING ==

Please do not hot link directly to the .zip file.  Please link to:
  http://pdub.net/projects/agilent-recovery-cd/

Also, please consider making a small donation there of any amount!


   == INFORMATION AND INSTRUCTIONS ==


Based on LS-120 120MB floppy disk data located at:
ftp://ftp.agilent.com/pub/callpub3/ddt/scope/548xx/Upg_Rec/4_3/
 
This bootable CD was pieced together in February 2010 after many hours of
frustration with an Agilent Infiniium 54825A/54825N Oscilloscope.  It was
constructed using a Windows 98 SE bootable CD image (emulating a Win98 SE
bootable 1.44 MB floppy disk) and the LS-120 floppy recovery disk data at
Agilent's FTP site.


LICENSE: This disc is Copyright 2010 Pat Wilbur. You are hereby licensed to use
this software without cost to rescue a broken oscilloscope system for which you
legally own all appropriate software licenses. You may copy or redistribute this
software only under the same terms as your current software licenses permit, and
the licenses for the software contained on this disc permit. Software contained
on this disc are copyright their respective owners, including Microsoft,
Agilent, Symantec, and possibly others. The author of this disc believes that
creation of this disc constitutes fair use of the floppy disk recovery data at 
the above Agilent FTP site URL.
 
 
DISCLAIMER: The author of this CD (Pat Wilbur) assumes ABSOLUTELY NO
responsibility for the operation of this CD or the following recovery
software, as he did not even write it (someone online supplied the base
boot CD image, and Agilent and Symantec produced the recovery software and
image).  No warranty for fitness, freedom from defect, or any other
warranty is guaranteed, neither expressly nor implied.  You agree to these
terms and to hold harmless the author of this CD (Pat Wilbur) for any 
direct, indirect, or consequential damages as a result of using this 
CD or the software contained on it, and usage of this software beyond this
point constitutes acceptance and agreement to these terms.
 
If you do not wish to agree to these terms and proceed, promptly disconnect
power from the device. Otherwise, if you agree to these terms, please continue.
 
 
NOTE: You are about to erase and lose ALL data on your hard drive!  This
includes saved test results, settings, the operating system, the software,
and any other files.  IF YOU DO NOT WISH TO DO THIS, or DO NOT KNOW WHAT 
YOU ARE DOING, then promptly disconnect power from the device.
 
 
 ======================
   WRITE THIS DOWN!!!
 ======================
  Author: Pat Wilbur
  E-mail: pdub ATATATATATATATAT pdub DOTDOTDOTDOTDOT net
 
  
INSTRUCTIONS:
 
 0. If this CD has saved you hours of frustration, e-mail and thank the 
    author. Seriously! He spent hours simplifying the process for others. :-)
  
 1. At the A:\ prompt, type 'R:' (without quotes) and press ENTER.
 
 2. IF you have a mouse connected type 'mouse' (without quotes) and press ENTER.
 
 3. Type 'ghost' (without quotes) and press ENTER.
 
 4. If a message appears titled, 'About NORTON Ghost', select 'OK' either by
    clicking it with the mouse or by pressing ENTER.
 
 5. Select 'Local' by clicking it with the mouse or highlighting it with the 
    arrow keys and pressing ENTER.
 
 6. Select 'Disk' by clicking on it or pressing ENTER. (Note: This should work
    fine for a typical oscilloscope, but if for some strange reason you have
    multiple partitions on your oscilloscope, choose 'Partition' and you're on
    your own from there.  If in doubt, choose 'Disk' like I just told you to.)
 
 7. Select 'From Image' by clicking on it or pressing ENTER.
 
 8. Select 'HP548RCV.GHO' (should allready be highlighted) and press ENTER.
 
 9. Select destination drive (1 should already be highlighted) and press ENTER.
 
 A. Next, on the drive details screen, a new size should already be filled in,
    so click on 'OK' or press TAB until 'OK' is selected and press ENTER.
 
 B. Proceed with disk load? Click on 'Yes' or press TAB until 'Yes' is selected
    and press ENTER. 
 
 C. If prompted to 'Insert next media and press enter to continue...' then
    simply ignore that message and proceed as if you had swapped disks. ;-)
    Click on 'OK' or make sure 'OK' is highlighted and press ENTER.
 
 D. If prompted to 'Insert next media and press enter to continue...' again then
    again ignore that message and proceed as if you had swapped disks. ;-)
    Click on 'OK' or make sure 'OK' is highlighted and press ENTER.

 E. When the recovery process finishes, restart your oscilloscope with the CD 
    removed. Make sure 'Reset Computer' is highlighted, remove CD, press ENTER.

 F. Windows should detect and install the drivers automatically. Windows will
    prompt you to restart the system to complete driver setup. You will need to
    have a keyboard or mouse connected at this point in order to have Windows
    finish the driver installation. Once the system restarts again, you should
    be up and running! You might want to perform self calibration and tests.

  
PW:pw, 02/2010